Go to main content
Master Crafted Home
Search

Search Master Crafted Home

Recessed Lighting Calculator: How Many Lights and How Far Apart?

Published on

To plan recessed lighting, pick a light level in footcandles (lumens per square foot) for the room, multiply by the floor area, divide by the lumens of one light and a coefficient of utilization from the room's proportions, then round up. The California Lighting Technology Center's guide says to space the lights 1 to 1.5 times the distance from the light to the task surface. This calculator does both steps and lays the lights out in an even grid.

Recessed lighting calculator

Enter your room and the light level you want. Results update as you type and the numbers are saved in the page address so you can bookmark or share them. Nothing leaves your browser. Sizes are in feet.

Room and light details

Illuminating Engineering Society targets, as reproduced by the California Lighting Technology Center. Changing this fills in the task height.

Height of the surface you want lit: 0 for the floor. Counters and tables are often about 3 ft; measure yours.

From the product label. ENERGY STAR bulbs replacing 60 W give at least 800 lm.

Your recessed lighting plan

How the recessed lighting calculator works

The calculator uses the lumen method from the California Lighting Technology Center's residential guide. The light fixtures sit in the ceiling, so the height that matters is the distance down to the surface you want lit. A tall, narrow room loses more light to its walls than a wide one, which the room cavity ratio and a coefficient of utilization (CU) capture. The number of lights is rounded up, then placed in an even grid whose spacing may not exceed 1.5 times the height above the task surface.

Lumen method and spacing
H     = ceiling height − task surface height
RCR   = 5 × H × (length + width) ÷ (length × width)
lights = round up (footcandles × area ÷ (lumens per light × CU))
spacing guide = 1 × H to 1.5 × H;  grid spacing = length ÷ columns and width ÷ rows
RCR
room cavity ratio, from 1 to 10 (the CU table stops at 10)
CU
coefficient of utilization, read from the table below and interpolated
footcandle
one lumen per square foot reaching the surface

Worked example

Given: a 14 ft × 12 ft room; 8 ft ceiling; target of 20 footcandles at 2.5 ft (a sitting area); 800 lumen lights.

  1. Height above the task surface: H = 8 − 2.5 = 5.5 ft
  2. Room cavity ratio: RCR = 5 × 5.5 × (14 + 12) ÷ (14 × 12) = 715 ÷ 168 = 4.26
  3. Coefficient of utilization (between 0.61 at RCR 4 and 0.55 at RCR 5): CU = 0.61 − 0.26 × 0.06 = 0.59
  4. Lumens needed at the lights: 20 × 168 ÷ 0.59 = 5,650 lm
  5. Number of lights: 5,650 ÷ 800 = 7.06, round up to 8
  6. Spacing limit (1.5 × H): 1.5 × 5.5 = 8.25 ft
  7. Grid of 4 along the length and 2 along the width: 14 ÷ 4 = 3.5 ft and 12 ÷ 2 = 6 ft apart; 1.75 ft and 3 ft from the walls

Answer: 8 recessed lights of 800 lumens in a 4 × 2 grid, 3.5 ft by 6 ft apart, giving about 23 footcandles on the 2.5 ft surface.

Published values used

Coefficient of utilization by room cavity ratio
Room cavity ratioCoefficient of utilizationSource
1 0.88Source 1
2 0.78Source 1
3 0.69Source 1
4 0.61Source 1
5 0.55Source 1
6 0.49Source 1
7 0.45Source 1
8 0.41Source 1
9 0.37Source 1
10 0.34Source 1

Table from the CLTC guide, which assumes 20% floor, 80% ceiling and 50% wall reflectance. Darker finishes lower the real figure.

Light level targets offered in the calculator (IES, via CLTC)
TaskFootcandlesWhere measuredSource
Living room, general 3FloorSource 1
Hallway 3FloorSource 1
Kitchen, general 5FloorSource 1
Showers and tubs 5FloorSource 1
Bedroom sitting area 202.5 ft above the floorSource 1
Reading in bed 203 ft above the floorSource 1
Vanity, casual inspection 203 ft above the floorSource 1
Vanity, grooming 305 ft 9 in above the floorSource 1
Kitchen sink 30Top of the sinkSource 1
Kitchen prep counters 50Prep surfacesSource 1

Recommended average levels, not code requirements. Heights follow the source where it gives one; the sink and prep counter heights are ours to set (about 3 ft is typical).

ENERGY STAR bulb brightness: minimum lumens by the watts of the bulb replaced
Standard bulbMinimum lumensSource
40 W 450Source 2
60 W 800Source 2
75 W 1,100Source 2
100 W 1,600Source 2
150 W 2,600Source 2

Assumptions and limits

  • This plans the ambient layer from the ceiling. Task lights (under cabinets, at the mirror, reading lamps), wall washing and accent lights are separate layers.
  • The CU table assumes light surfaces (80% ceiling, 50% walls, 20% floor). Dark walls and dark floors absorb more light, so rooms like that need more lumens than shown. The method also has no allowance for dimming or the dirt and lumen loss over time.
  • The grid is rectangular and even. Real rooms have beams, vents, joists, kitchen islands and furniture that move the lights; treat this as a plan to adjust, not a drawing.
  • The spacing range is the CLTC rule of thumb. Beam angle and trim change how far a light carries, so check the product's spacing data when you buy.
  • Numbers are as published on 2026-11-13. Light-level targets are recommendations, not a building code. Electrical work should follow your local code and be done by a qualified person.

Your questions answered

How many recessed lights do I need for a 12 x 14 room?

It depends on the light level you want and how bright each light is. For general light in a living room the IES target reproduced by the California Lighting Technology Center is only 3 footcandles at the floor, which a 12 x 14 ft room with an 8 ft ceiling reaches with two lights of 800 lumens by the lumen count alone, although the spacing limit makes the calculator plan a grid of four. For seating areas with reading light (20 footcandles at 2.5 ft) the same room needs about eight. Pick your target above and the calculator gives the count.

How far apart should recessed lights be?

The CLTC guide's rule of thumb is 1 to 1.5 times the distance from the light to the main task plane. With an 8 ft ceiling and a task plane 2.5 ft above the floor that is 5.5 ft to about 8.25 ft apart. The calculator never lets the grid exceed the upper figure, and it will add lights if the room is too large for the lumen count alone to meet it.

Is it true that the spacing should be half the ceiling height?

That is a widely repeated installer convention (an 8 ft ceiling gives 4 ft spacing), not a published standard. It is tighter than the published range of 1 to 1.5 times the task distance for most task heights, so it tends to produce more lights than the lumens need. We use the published range and show it.

How far from the wall should the first light be?

In an even grid the outer lights sit half a spacing from the wall, which is how this calculator lays the grid out, so the light is shared evenly. Many designers shift lights further out to wash a wall or closer to light a wall of art or shelving. Treat the figure as a starting point for an even ambient layer.

What is a footcandle and how does it relate to lumens?

A footcandle is one lumen falling on one square foot. A room of 168 sq ft that should average 20 footcandles needs 3,360 lumens to reach the task surface, before losses. The calculator divides by the coefficient of utilization to allow for light that is absorbed by walls and ceiling or never reaches the task plane.

How many lumens should each recessed light have?

ENERGY STAR's fixture fact sheet suggests about 400 to 800 lumens in living rooms and bedrooms, and 1,000 or more in kitchens, bathrooms and home offices. It also lists the minimum lumens of an ENERGY STAR bulb by the watts of the bulb it replaces: 450 for 40 W, 800 for 60 W, 1,100 for 75 W and 1,600 for 100 W. Read the lumens on your product's label.

Does the result include dimmers, trims or colour temperature?

No. The method counts lumens delivered to a surface and nothing else. A narrow trim with a deep baffle sends less light into the room than the lumens on the box imply, and a dimmer lowers the output. If you plan to dim most of the time, choose a higher-lumen light. Colour temperature does not change the count; ENERGY STAR describes 2200K to 3000K as warm and 3500K to 5000K as neutral to cool.

Can I use this for a bathroom or kitchen?

Yes for the ambient layer. Pick the vanity, sink or prep counter target and set the task plane height. Vanity grooming (30 footcandles at 5 ft 9 in) is better served by lights at the mirror than by the ceiling alone, so treat the ceiling result as the general layer and add wall lights. Wet areas need fixtures rated for them; check the product label.

References

  1. California Lighting Technology Center, UC Davis: High-Efficacy Residential Lighting (Dec 2014): lumen method, coefficient of utilization table, spacing rule of thumb and IES recommended light levels (cltc.ucdavis.edu) Accessed 2026-11-13.
  2. ENERGY STAR: Fixtures Made Easy fact sheet: lumens by room and minimum lumens by bulb wattage (energystar.gov) Accessed 2026-11-13.

More guides like this